- stunnel-users - stunnel.org

Re: [stunnel-users] "Broken pipe" issue
by Ron McWilliams 21 Jun '13

21 Jun '13

I have the same issue with the broken pipe on my stunnel. Here is the revealing log clip. appsadmin@MIRTHTEST:/etc/stunnel.d$ sudo tail -f /var/log/stunnel_mirth.log 2013.06.21 17:28:03 LOG7[30980:3077569344]: Service hl7_client prod finished (1 left) 2013.06.21 17:28:03 LOG7[30980:3077569344]: str_stats: 0 block(s), 0 data byte(s), 0 control byte(s) 2013.06.21 17:28:14 LOG6[30980:3073227584]: SSL connected: previous session reused 2013.06.21 17:28:14 LOG7[30980:3073227584]: Socket closed on read 2013.06.21 17:28:14 LOG7[30980:3073227584]: Sending SSL write shutdown 2013.06.21 17:28:14 LOG6[30980:3073227584]: SSL_shutdown successfully sent close_notify 2013.06.21 17:28:24 LOG5[30980:3073227584]: Error detected on socket (read) file descriptor: Broken pipe (32) 2013.06.21 17:28:24 LOG5[30980:3073227584]: Connection reset: 661 bytes sent to SSL, 124 bytes sent to socket 2013.06.21 17:28:24 LOG7[30980:3073227584]: Service hl7_client prod finished (0 left) 2013.06.21 17:28:24 LOG7[30980:3073227584]: str_stats: 0 block(s), 0 data byte(s), 0 control byte(s) Was there a simple edit to the conf file and if so, could you send the sample settings. Thank you, rmcwilli

1 0

Re: [stunnel-users] Broken pipes and TCP resets on parallel requests over stunnel
by Ron McWilliams 21 Jun '13

21 Jun '13

I have essentially the same issue. We were successfully sending messages and receiving ACK prior to this glitch. I am on Ubuntu 12.04 LTS using stunnel 4.50. appsadmin@MIRTHTEST:/etc/stunnel.d$ sudo tail -f /var/log/stunnel_mirth.log 2013.06.21 17:28:03 LOG7[30980:3077569344]: Service hl7_client prod finished (1 left) 2013.06.21 17:28:03 LOG7[30980:3077569344]: str_stats: 0 block(s), 0 data byte(s), 0 control byte(s) 2013.06.21 17:28:14 LOG6[30980:3073227584]: SSL connected: previous session reused 2013.06.21 17:28:14 LOG7[30980:3073227584]: Socket closed on read 2013.06.21 17:28:14 LOG7[30980:3073227584]: Sending SSL write shutdown 2013.06.21 17:28:14 LOG6[30980:3073227584]: SSL_shutdown successfully sent close_notify 2013.06.21 17:28:24 LOG5[30980:3073227584]: Error detected on socket (read) file descriptor: Broken pipe (32) 2013.06.21 17:28:24 LOG5[30980:3073227584]: Connection reset: 661 bytes sent to SSL, 124 bytes sent to socket 2013.06.21 17:28:24 LOG7[30980:3073227584]: Service hl7_client prod finished (0 left) 2013.06.21 17:28:24 LOG7[30980:3073227584]: str_stats: 0 block(s), 0 data byte(s), 0 control byte(s) rmcwilli

1 0

certificate verify failed
by Roman Tuchyna 19 Jun '13

19 Jun '13

Hi All, I'm trying to create SSl tunnel between my server (Win 2008 R2, 4.56 version of stunnel) and remote application server - I have merged both root and sub certificate into 1 file and it looks like it can verify them and accept them as well, but then it tries to verify it at depth=0 and says certificate not found in local repository. Am I missing anything here ? (I modified messages to not disclose details of certificates in the debug below). Thank you! BR, Roman 2013.06.18 11:22:34 LOG7[272:2156]: Service [SZX] started 2013.06.18 11:22:34 LOG5[272:2156]: Service [SZX] accepted connection from 127.0.0.1:49397 2013.06.18 11:22:34 LOG6[272:2156]: connect_blocking: connecting 10.254.0.21:443 2013.06.18 11:22:34 LOG7[272:2156]: connect_blocking: s_poll_wait 10.254.0.21:443: waiting 10 seconds 2013.06.18 11:22:34 LOG5[272:2156]: connect_blocking: connected 10.254.0.21:443 2013.06.18 11:22:34 LOG5[272:2156]: Service [SZX] connected remote server from 192.168.20.23:49398 2013.06.18 11:22:34 LOG7[272:2156]: Remote socket (FD=396) initialized 2013.06.18 11:22:34 LOG7[272:2156]: SNI: sending servername: 10.254.0.21 2013.06.18 11:22:34 LOG7[272:2156]: SSL state (connect): before/connect initialization 2013.06.18 11:22:34 LOG7[272:2156]: SSL state (connect): SSLv3 write client hello A 2013.06.18 11:22:34 LOG7[272:2156]: SSL state (connect): SSLv3 read server hello A 2013.06.18 11:22:34 LOG7[272:2156]: Starting certificate verification: depth=2, /CN=xxx RootCA 2013.06.18 11:22:34 LOG5[272:2156]: Certificate accepted: depth=2, /CN=xxx RootCA 2013.06.18 11:22:34 LOG7[272:2156]: Starting certificate verification: depth=1, /CN=xxx 2013.06.18 11:22:34 LOG5[272:2156]: Certificate accepted: depth=1, /CN=xxx SubCA1 2013.06.18 11:22:34 LOG7[272:2156]: Starting certificate verification: depth=0, /C=zzz 2013.06.18 11:22:34 LOG4[272:2156]: CERT: Certificate not found in local repository 2013.06.18 11:22:34 LOG4[272:2156]: Certificate check failed: depth=0, /C=zzz 2013.06.18 11:22:34 LOG7[272:2156]: SSL alert (write): fatal: certificate unknown 2013.06.18 11:22:34 LOG3[272:2156]: SSL_connect: 14090086: error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate verify failed 2013.06.18 11:22:34 LOG5[272:2156]: Connection reset: 0 byte(s) sent to SSL, 0 byte(s) sent to socket 2013.06.18 11:22:34 LOG7[272:2156]: Remote socket (FD=396) closed 2013.06.18 11:22:34 LOG7[272:2156]: Local socket (FD=376) closed 2013.06.18 11:22:34 LOG7[272:2156]: Service [SZX] finished (0 left)

3 2

stunnel RHEL 6.3 and HTTPS header fields
by xxxxxxxxxxxxxxxxx 16 Jun '13

16 Jun '13

I'm an Stunnel newbie so forgive me if this question has been asked previously. I am using stunnel to accept a connection from http://127.0.0.1:someport/url/to/wsdland connect to hostname.somewhere.abc:443 Everything is working fine with the exception of a certain endpoint that responds with an HTTP status code of 403 "forbidden". What I have determined is that the server is rejecting the request due to the HTTP "Host:" field value, it's set to 127.0.0.1. Is there anyway to pass the value of the config file "connect" property instead (in my case "hostname.somewhere")?I have tried various config settings without success. Config entry: [testnesiis]client = yesaccept = 127.0.0.1:1445connect = testnesiis:443;protocolHost = testnesiis:443protocol = proxy;sni = testnesiis;transparent = both Thanks and Kudos to the authors of stunnel !

2 1

Certificate failure to verify with verify = 4 option
by Thomas Eifert 16 Jun '13

16 Jun '13

Greetings; Stunnel 4.56 running under Win 7 SP1 x86. Recently, the owners of a server I regularly connect to updated their server certificate; the former had expired at the end of May. As soon as that event occurred, I deleted the old certificate, then used the "save peer certificate" function of Stunnel to get the updated one. However, the new certificate fails to verify, even with the verify = 4 option in Stunnel. The error message is similar to what I used to get when doing a verify = 3 with some certificates. The general error output of Stunnel is: CERT: Verification error: unable to get local issuer certificate 2013.06.09 16:37:46 LOG4[608:2336]: Certificate check failed: depth=0 When I open the new certificate with: openssl x509 -text -in certname.pem and view the certificate details, I'm not seeing anything obvious. The certificate is within a valid date range, and contains the same basic elements as other certs I've viewed. The certificate appears to have been issued by Startcom LLC. If I comment out the verify statement, I'm able to successfully negotiate an SSL connection with the server. I realize that this may be more of an openssl issue than an issue with Stunnel. Nevertheless, I thought I'd start here and throw it out to the floor for comments. Anyone have any ideas or have run into this issue? Regards, Thomas -- Attention: This message and all attachments are private and may contain information that is confidential and privileged. If you received this message in error, please notify the sender by reply email and delete the message immediately.

2 2

tuning/multiple stunnel instance
by William Kwan 13 Jun '13

13 Jun '13

Dear all, I would like to find out if there's anyway to tune stunnel or what's the best practice you would recommend. I have a bit more than 100 sessions defined in stunnel.conf. It appears that clients started to see latency increase. Would you say 1. Split the conf file to multiple conf files and start multiple stunnel with each conf file? 2. Any way to tune stunnel to run muliple process with more threads? 3. Any other options? Thanks Will

2 1

stunnel doesn't create tunnel
by Roman Tuchyna 13 Jun '13

13 Jun '13

Hi All, I'm trying to create SSL tunnel between my server and remote application server and according to log file, stunnel fails to 0.0.0.0:43 Service [SZR] (FD=716) bound to 0.0.0.0:443 (although connect and accept are configured for this service). I'm using stunnel on Windows and apparently I'm doing something wrong - any hint or advice would be appreciated. I was searching for the reason, but couldn't find any pointer... Thank you! BR, Roman 2013.06.13 16:25:19 LOG7[2884:3032]: Dispatching signals from the signal pipe 2013.06.13 16:25:19 LOG7[2884:3032]: Processing SIGNAL_RELOAD_CONFIG 2013.06.13 16:25:19 LOG5[2884:3032]: Reading configuration from file stunnel.conf 2013.06.13 16:25:19 LOG5[2884:3032]: FIPS mode is enabled 2013.06.13 16:25:19 LOG7[2884:3032]: Compression not enabled 2013.06.13 16:25:19 LOG7[2884:3032]: Snagged 64 random bytes from C:/.rnd 2013.06.13 16:25:19 LOG7[2884:3032]: Wrote 1024 new random bytes to C:/.rnd 2013.06.13 16:25:19 LOG7[2884:3032]: PRNG seeded successfully 2013.06.13 16:25:19 LOG6[2884:3032]: Initializing service [SZR] 2013.06.13 16:25:19 LOG7[2884:3032]: Loaded verify certificates from SZR.pem 2013.06.13 16:25:19 LOG7[2884:3032]: Loaded SZR.pem revocation lookup file 2013.06.13 16:25:19 LOG7[2884:3032]: SSL options set: 0x01000004 2013.06.13 16:25:19 LOG5[2884:3032]: Configuration successful 2013.06.13 16:25:19 LOG7[2884:3032]: Closing service [SZR] 2013.06.13 16:25:19 LOG7[2884:3032]: Service [SZR] closed (FD=716) 2013.06.13 16:25:19 LOG7[2884:3032]: Sessions cached before flush: 0 2013.06.13 16:25:19 LOG7[2884:3032]: Sessions cached after flush: 0 2013.06.13 16:25:19 LOG7[2884:3032]: Service [SZR] closed 2013.06.13 16:25:19 LOG7[2884:3032]: Service [SZR] (FD=716) bound to 0.0.0.0:443 2013.06.13 16:25:19 LOG7[2884:3032]: Signal pipe is empty

1 0

Re: [stunnel-users] Getting Stunnel working with Verizon.net SMTP
by Gary Kuznitz 13 Jun '13

13 Jun '13

Hi Jochen, With your help I selected "Do not use CRAM-MD5 authentication even if it is advertised" It's now woking. Thank you very much for your help. Do you know if there is any way to remove the emails with the user name and password from the archives? Thanks, Gary On 12 Jun 2013 at 23:08, Jochen (Jochen Bern <Jochen.Bern(a)LINworks.de>) commented about Re: [stunnel-users] Getting Stunnel working with : > On 12.06.2013 21:28, Gary Kuznitz wrote: > > On your first post I didn't see the difference in port numbers. I have corrected that. > > I'm getting this log from my email client: > > --- Wed, 12 Jun 2013 12:22:46 --- > > Connect to 'localhost' port 10115, timeout 60. > > 12:22:46.960 [*] Connection established to 127.0.0.1 > > 12:22:47.226 >> 0120 220 vms173007pub.verizon.net -- Server ESMTP (Sun Java(tm) > > System Messaging Server 7u2-7.02 32bit (built Apr 16 2009))\0D\0A > > First and foremost, this shows that your e-mail client can now talk to > the server, which means that stunnel's job (the SSL negotiation) gets > done successfully. > > > 12:22:47.288 >> 0042 250-AUTH DIGEST-MD5 PLAIN LOGIN CRAM-MD5\0D\0A > > 12:22:47.288 >> 0022 250-AUTH=LOGIN PLAIN\0D\0A > > This part of the server's reply to the EHLO command shows the auth > mechanisms the server supports; CRAM-MD5 is listed ... > > > 12:22:47.288 << 0015 AUTH CRAM-MD5\0D\0A > > ... and your client requests it. > > > 12:22:47.335 >> 0050 334 PDEzNTYyOTY5MjEuMTIxMTA1NTFAdm1zMTczMDA3Pg==\0D\0A > > The servers issues (a base64 encoded version of) > "<1356296921.12110551@vms173007>" as a "random" string challenge. > > > 12:22:47.335 << 0058 YXR1cHJlcyBkYTlmZTI3MWFjODNjYWUxOTVjNmZhZWQ5ZGE0NTUzYg==\0D\0A > > This is a base64 encoded version of "atupres > da9fe271ac83cae195c6faed9da4553b". "atupres" should be your username and > da9fe271ac83cae195c6faed9da4553b the HMAC-MD5 digest of the challenge > with your password as the key. > > I don't know a tool to compute HMAC-MD5 digests that is readily > available under Windows, I'm afraid. If you're desperate, try > http://www.freeformatter.com/hmac-generator.html > (note that they won't know a) on which server and b) with what username > you'll be using the password ...). > > > 12:22:47.397 >> 0066 500 5.7.0 Unknown AUTH error -1 (Internal authentication error).\0D\0A > > ... and there the server says it cannot verify that. > > > Do you have any idea why I am getting [that]? > > I can think of several *possible* reasons, but ultimately, the server > doesn't tell us what exactly is wrong. > > 1. It may be that the server is announcing CRAM-MD5 auth though it > actually does *not* support it. (The DIGEST-MD5 and CRAM-MD5 mechs > require that the server *knows* the (plaintext) password, while for > PLAIN and LOGIN, storing only a hash of the password is enough, and > foils attackers who manage to steal a copy of the password database.) > Enforcing use of a different mechanism can probably be done through > your e-mail client's settings, but I'm afraid that it's usually > rather cryptic how exactly to do that ... > If you want to have a *manual* try at another mech, here's a web > page explaining what to input for PLAIN and LOGIN: > http://www.gadgetwiz.com/protocols/smtp-auth-example.html > and here's an MS KB article with a base64 en-/decoder: > http://support.microsoft.com/kb/191239 > Problem is that the strings to be base64 encoded are supposed *not* > to have an end-of-line, and sometimes even to contain NUL bytes > ("\0") ... Verify that your method of choice properly reproduces the > examples in the howto page. :-C > 2. I'm a bit surprised that your username supposedly is "atupres", > rather than "atupres(a)your.dom.ain", "atupres%your.dom.ain" or > something to that effect ... ? > 3. The obvious one, a mistyped password ... > > Regards, > J. Bern > -- > *NEU* - NEC IT-Infrastruktur-Produkte im <http://www.linworks-shop.de/>: > Server--Storage--Virtualisierung--Management SW--Passion for Performance > Jochen Bern, Systemingenieur --- LINworks GmbH <http://www.LINworks.de/> > Postfach 100121, 64201 Darmstadt | Robert-Koch-Str. 9, 64331 Weiterstadt > PGP (1024D/4096g) FP = D18B 41B1 16C0 11BA 7F8C DCF7 E1D5 FAF4 444E 1C27 > Tel. +49 6151 9067-231, Zentr. -0, Fax -299 - Amtsg. Darmstadt HRB 85202 > Unternehmenssitz Weiterstadt, Geschäftsführer Metin Dogan, Oliver Michel

2 1

Re: [stunnel-users] Getting Stunnel working with Verizon.net SMTP
by Gary Kuznitz 12 Jun '13

12 Jun '13

Thank you very much for working with me on resolving this. On your first post I didn't see the difference in port numbers. I have corrected that. Thank you for catching it. It did get me closer to resolving the issue. I'm getting this log from my email client: --- Wed, 12 Jun 2013 12:22:46 --- Connect to 'localhost' port 10115, timeout 60. 12:22:46.960 [*] Connection established to 127.0.0.1 12:22:47.226 >> 0120 220 vms173007pub.verizon.net -- Server ESMTP (Sun Java(tm) System Messaging Server 7u2-7.02 32bit (built Apr 16 2009))\0D\0A 12:22:47.226 << 0023 EHLO [192.168.168.11]\0D\0A 12:22:47.288 >> 0030 250-vms173007pub.verizon.net\0D\0A 12:22:47.288 >> 0014 250-8BITMIME\0D\0A 12:22:47.288 >> 0016 250-PIPELINING\0D\0A 12:22:47.288 >> 0014 250-CHUNKING\0D\0A 12:22:47.288 >> 0009 250-DSN\0D\0A 12:22:47.288 >> 0025 250-ENHANCEDSTATUSCODES\0D\0A 12:22:47.288 >> 0010 250-HELP\0D\0A 12:22:47.288 >> 0044 250-XLOOP AD6DF29B04183351BAD9935B9A483ABE\0D\0A 12:22:47.288 >> 0042 250-AUTH DIGEST-MD5 PLAIN LOGIN CRAM-MD5\0D\0A 12:22:47.288 >> 0022 250-AUTH=LOGIN PLAIN\0D\0A 12:22:47.288 >> 0010 250-ETRN\0D\0A 12:22:47.288 >> 0019 250-NO-SOLICITING\0D\0A 12:22:47.288 >> 0019 250 SIZE 20971520\0D\0A 12:22:47.288 << 0015 AUTH CRAM-MD5\0D\0A 12:22:47.335 >> 0050 334 PDEzNTYyOTY5MjEuMTIxMTA1NTFAdm1zMTczMDA3Pg==\0D\0A 12:22:47.335 << 0058 YXR1cHJlcyBkYTlmZTI3MWFjODNjYWUxOTVjNmZhZWQ5ZGE0NTUzYg==\0D\0A 12:22:47.397 >> 0066 500 5.7.0 Unknown AUTH error -1 (Internal authentication error).\0D\0A 12:22:50.845 << 0006 QUIT\0D\0A 12:22:50.892 >> 0034 221 2.3.0 Bye received. Goodbye.\0D\0A 12:22:50.892 --- Connection closed normally at Wed, 12 Jun 2013 12:22:50. ---\0A\0A I'm getting this in the Stunnel.log 2013.06.12 12:22:46 LOG7[660:2460]: New thread created 2013.06.12 12:22:46 LOG7[660:896]: Service [Verizon-smtp] started 2013.06.12 12:22:46 LOG5[660:896]: Service [Verizon-smtp] accepted connection from 127.0.0.1:52721 2013.06.12 12:22:46 LOG6[660:896]: connect_blocking: connecting 206.46.232.12:465 2013.06.12 12:22:46 LOG7[660:896]: connect_blocking: s_poll_wait 206.46.232.12:465: waiting 10 seconds 2013.06.12 12:22:46 LOG5[660:896]: connect_blocking: connected 206.46.232.12:465 2013.06.12 12:22:46 LOG5[660:896]: Service [Verizon-smtp] connected remote server from 192.168.168.11:52722 2013.06.12 12:22:46 LOG7[660:896]: Remote socket (FD=384) initialized 2013.06.12 12:22:46 LOG7[660:896]: SNI: sending servername: outgoing.verizon.net 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): before/connect initialization 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 write client hello A 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 read server hello A 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 read server certificate A 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 read server key exchange A 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 read server done A 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 write client key exchange A 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 write change cipher spec A 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 write finished A 2013.06.12 12:22:46 LOG7[660:896]: SSL state (connect): SSLv3 flush data 2013.06.12 12:22:47 LOG7[660:896]: SSL state (connect): SSLv3 read finished A 2013.06.12 12:22:47 LOG7[660:896]: 2 items in the session cache 2013.06.12 12:22:47 LOG7[660:896]: 2 client connects (SSL_connect()) 2013.06.12 12:22:47 LOG7[660:896]: 2 client connects that finished 2013.06.12 12:22:47 LOG7[660:896]: 0 client renegotiations requested 2013.06.12 12:22:47 LOG7[660:896]: 0 server connects (SSL_accept()) 2013.06.12 12:22:47 LOG7[660:896]: 0 server connects that finished 2013.06.12 12:22:47 LOG7[660:896]: 0 server renegotiations requested 2013.06.12 12:22:47 LOG7[660:896]: 0 session cache hits 2013.06.12 12:22:47 LOG7[660:896]: 0 external session cache hits 2013.06.12 12:22:47 LOG7[660:896]: 0 session cache misses 2013.06.12 12:22:47 LOG7[660:896]: 0 session cache timeouts 2013.06.12 12:22:47 LOG6[660:896]: SSL connected: new session negotiated 2013.06.12 12:22:47 LOG6[660:896]: Negotiated TLSv1/SSLv3 ciphersuite: DHE-RSA-AES256-SHA (256-bit encryption) 2013.06.12 12:22:47 LOG6[660:896]: Compression: null, expansion: null 2013.06.12 12:22:50 LOG6[660:896]: Read socket closed (readsocket) 2013.06.12 12:22:50 LOG7[660:896]: Sending close_notify alert 2013.06.12 12:22:50 LOG7[660:896]: SSL alert (write): warning: close notify 2013.06.12 12:22:50 LOG6[660:896]: SSL_shutdown successfully sent close_notify alert 2013.06.12 12:22:50 LOG7[660:896]: SSL alert (read): warning: close notify 2013.06.12 12:22:50 LOG6[660:896]: SSL closed (SSL_read) 2013.06.12 12:22:50 LOG7[660:896]: Sent socket write shutdown 2013.06.12 12:22:50 LOG5[660:896]: Connection closed: 102 byte(s) sent to SSL, 544 byte(s) sent to socket 2013.06.12 12:22:50 LOG7[660:896]: Remote socket (FD=384) closed 2013.06.12 12:22:50 LOG7[660:896]: Local socket (FD=216) closed 2013.06.12 12:22:50 LOG7[660:896]: Service [Verizon-smtp] finished (0 left) Do you have any idea why I am getting: 12:22:47.397 >> 0066 500 5.7.0 Unknown AUTH error -1 (Internal authentication error).\0D\0A Thank you, Gary On 12 Jun 2013 at 20:36, Jochen (Jochen Bern <Jochen.Bern(a)LINworks.de>) commented about Re: [stunnel-users] Getting Stunnel working with : > On 12.06.2013 19:48, Gary Kuznitz wrote: > > Thanks for showing me how to test SSL. I installed openssl and ran the test. This is > > what I received back. > > > > C:\Programs\OpenSSL-Win32\bin>openssl s_client -connect smtp.verizon.net:465 > [...] > > Verify return code: 19 (self signed certificate in certificate chain) > > --- > > At this point, the SSL layer of the connection has been set up (s_client > ignores the non-null verification result) and the actual payload > protocol can start to do its thing. The payload protocol is SMTP, so the > server throws you a hello line: > > > 220 vms173025pub.verizon.net -- Server ESMTP (Sun Java(tm) System Messaging Server 7u2-7.02 32bit (built Apr 16 2009)) > > and then waits for the client to send its requests. Since you apparently > didn't enter anything, the server obviously terminated the connection with: > > > 421 4.4.2 Timeout while waiting for command. > > An actual SMTP session with an *attempt* at transferring an e-mail would > look like, e.g.: > > > 220 vms173023pub.verizon.net -- Server ESMTP (Sun Java(tm) System Messaging Server 7u2-7.02 32bit (built Apr 16 2009)) > > HELO this.is.my.laptop > > 250 vms173023pub.verizon.net OK, [unknown] [213.157.4.156]. > > MAIL FROM:<Jochen.Bern(a)LINworks.de> > > 550 5.7.1 Authentication Required > > rSET > > 250 2.5.0 Ok. > > QUIT > > (The lines starting with a three-digit SMTP status code number are sent > by the server; the 5xx code signals a permanent error; the lines > starting with a four-letter SMTP command are sent by the client, i.e., I > typed them into the s_client; and I typed "rSET" instead of the normal > "RSET" because s_client takes every line starting with an *uppercase* > 'R' as a command to do an SSL renegotiation.) > > > It sounds like something is wrong on this end. Any ideas? > > What about the two *****DIFFERING***** port numbers I pointed out in > your posted data? > > >> On 12.06.2013 05:12, Gary Kuznitz wrote: > >>> [Verizon-smtp] > >>> client = yes > >>> accept = 11015 > >> ^##^^ > >> [...] > >>> --- Tue, 11 Jun 2013 16:38:55 --- > >>> Connect to 'localhost' port 10115, timeout 60. > >> ^##^^ > > I don't actually use stunnel (subscribed to the list when I had a need > that I later fulfilled with socat, but that's Unix/Linux only), so I > don't know whether stunnel has a problem with the self-signed cert ... > > Regards, > J. Bern > -- > *NEU* - NEC IT-Infrastruktur-Produkte im <http://www.linworks-shop.de/>: > Server--Storage--Virtualisierung--Management SW--Passion for Performance > Jochen Bern, Systemingenieur --- LINworks GmbH <http://www.LINworks.de/> > Postfach 100121, 64201 Darmstadt | Robert-Koch-Str. 9, 64331 Weiterstadt > PGP (1024D/4096g) FP = D18B 41B1 16C0 11BA 7F8C DCF7 E1D5 FAF4 444E 1C27 > Tel. +49 6151 9067-231, Zentr. -0, Fax -299 - Amtsg. Darmstadt HRB 85202 > Unternehmenssitz Weiterstadt, Geschäftsführer Metin Dogan, Oliver Michel

1 0

Getting Stunnel working with Verizon.net SMTP
by Gary Kuznitz 12 Jun '13

12 Jun '13

I can't seem to connect with email at Verizon.net SMTP. I can connect with POP3. The Stunnel.log shows: 2013.06.11 19:27:04 LOG5[3752:2524]: stunnel 4.56 on x86-pc-msvc-1500 platform 2013.06.11 19:27:04 LOG5[3752:2524]: Compiled/running with OpenSSL 1.0.1e-fips 11 Feb 2013 2013.06.11 19:27:04 LOG5[3752:2524]: Threading:WIN32 Sockets:SELECT,IPv6 SSL:ENGINE,OCSP,FIPS 2013.06.11 19:27:04 LOG5[3752:2524]: Reading configuration from file stunnel.conf 2013.06.11 19:27:04 LOG5[3752:2524]: FIPS mode is enabled 2013.06.11 19:27:04 LOG5[3752:2524]: Configuration successful I have IPv6 turned off in my network settings. The Stunnel.conf looks like this: output = stunnel.log cert = stunnel.pem options = NO_SSLv2 [Verizon-pop3] client = yes accept = 11014 connect = pop.verizon.net:995 delay = yes [Verizon-smtp] client = yes accept = 11015 connect = smtp.verizon.net:465 delay = yes I do not have SSL turned on in my email client. The log from my email client looks like this: --- Tue, 11 Jun 2013 16:38:55 --- Connect to 'localhost' port 10115, timeout 60. 16:38:56.897 15: Peer connect failure (the host has refused the connection). The Verizon account is FIOS. I am not connected directly to the Verizon ISP. I can't send email without SSL. Does anyone have any idea how I can get this working? Thanks, Gary Kuznitz

3 4

Certificate failure to verify with verify = 4 option
by Thomas Eifert 10 Jun '13

10 Jun '13

Correction: The cert issuer is Startcom Ltd, not Startcom LLC. -- Greetings; Stunnel 4.56 running under Win 7 SP1 x86. Recently, the owners of a server I regularly connect to updated their server certificate; the former had expired at the end of May. As soon as that event occurred, I deleted the old certificate, then used the "save peer certificate" function of Stunnel to get the updated one. However, the new certificate fails to verify, even with the verify = 4 option in Stunnel. The error message is similar to what I used to get when doing a verify = 3 with some certificates. The general error output of Stunnel is: CERT: Verification error: unable to get local issuer certificate 2013.06.09 16:37:46 LOG4[608:2336]: Certificate check failed: depth=0 When I open the new certificate with: openssl x509 -text -in certname.pem and view the certificate details, I'm not seeing anything obvious. The certificate is within a valid date range, and contains the same basic elements as other certs I've viewed. The certificate appears to have been issued by Startcom LLC. If I comment out the verify statement, I'm able to successfully negotiate an SSL connection with the server. I realize that this may be more of an openssl issue than an issue with Stunnel. Nevertheless, I thought I'd start here and throw it out to the floor for comments. Anyone have any ideas or have run into this issue? Regards, Thomas -- Attention: This message and all attachments are private and may contain information that is confidential and privileged. If you received this message in error, please notify the sender by reply email and delete the message immediately. _______________________________________________ stunnel-users mailing list stunnel-users(a)stunnel.org https://www.stunnel.org/cgi-bin/mailman/listinfo/stunnel-users

3 3

weird stunnel problem
by Stephen Griffin 03 Jun '13

03 Jun '13

Hello A few days ago we ran into issue where the number of stunnel threads sky rocketed to over 3000 open stunnel threads. When this happen connections to our website slowed down considerably or failed to connect. It was resolved by flipping to our other proxy which accepted any new connections. It took about 5 minutes for the threads to die off on the other proxy. I was wondering if anyone has come across this problem? Here are some details of our stunnel version and config. Stunnel 4.44 with patch for x-forwarder [root@brm-proxy01 ~]# stunnel -version stunnel 4.44 on x86_64-unknown-linux-gnu platform Compiled/running with OpenSSL 1.0.0-fips 29 Mar 2010 Threading:PTHREAD SSL:ENGINE Auth:LIBWRAP Sockets:POLL,IPv6 Global options: debug = daemon.notice pid = /var/run/stunnel.pid RNDbytes = 64 RNDfile = /dev/urandom RNDoverwrite = yes Service-level options: ciphers = ALL:!SSLv2:!aNULL:!EXP:!LOW:-MEDIUM:RC4:+HIGH curve = prime256v1 session = 300 seconds sslVersion = TLSv1 for client, all for server stack = 65536 bytes TIMEOUTbusy = 300 seconds TIMEOUTclose = 60 seconds TIMEOUTconnect = 10 seconds TIMEOUTidle = 43200 seconds verify = none appriacated Our stunnel.conf. /etc/stunnel/stunnel.conf #sslVersion = TLSv1 pid = /var/run/stunnel.pid syslog = yes output = /var/log/stunnel.log debug = 3 [https] cert = /etc/stunnel/ssl/wildcard.blah.com.pem accept = 443 connect = 80 xforwardedfor = yes TIMEOUTbusy = 300 TIMEOUTclose = 0 TIMEOUTconnect = 10 TIMEOUTidle = 60 Is there anything we could add for performance tuning in stunnel? Any suggestions on what I could look for when this happens again would be appreciated. Our platform does between 2000 to 3000 rpm (request per minute) during peak hours. We constantly see a lot of these messages every hour but I am not sure what is happening as the connections seem to be working. SSL_accept: Peer suddenly disconnected There was a higher spike of them as per the normal rate during our incident described above. Thanks Stephen Griffin Sr. System Administrator www.achievers.com<http://www.achievers.com/> Confidentiality: The information contained in this e-mail and any attachments are confidential. If you are not the intended recipient, you may not copy or distribute this information. If you have received this communication in error, please notify the sender immediately and delete it from your system.

1 0

x-forwarded-for.patch for stunnel 4.55/4.56
by Shannon Carver 17 May '13

17 May '13

Hi all, Just wondering if anyone know's a an xforwardedfor patch available for the latest versions of stunnel? Thanks Shannon Carver

2 1

Strange Stunnel crash (no errors, issues, anything)
by Alfred Kernaghan 17 May '13

17 May '13

Hi, Long time lurker, new poster though! I've got two servers running Stunnel v2.54 (yet to upgrade as I've been waiting for an x-forwardfor patch to become available). I noticed recently that one Stunnel nodes had exited, requiring a restart. I'm not sure if it's a co-incidence, but I've only just changed the cert on both installs last night. This, of course, is very concerning as it's only just become a problem, but being the core SSL endpoint, it knocks our server offline until it's restarted. Now comes the interesting bit, I've run the SSL Labs SSL Health check at https://www.ssllabs.com/ssltest/ just to see if anything comes out of it, and noticed that without fail every time it runs (and the first server is online) it'll know Stunnel offline as it goes through it's tests: *"Testing TLS v1.0...." "Testing TLS v1.2...."* *-- SERVER OFFLINE --* This was noticed by a fluke, but appears to happen every time I restart and then rerun the test. I'm not getting any segfaults, or errors from stunnel, and it only affects the one (primary) server. Can anyone shed any light as to what might be causing it, how I can get any more info out of stunnel, or better yet, fix it completely? Thanks all Alfie

2 2

Error with stunnel 4.56 on Ubuntu 12
by Laura Fried 12 May '13

12 May '13

I am getting a success with doing the configure, make and make install. However when I go to start up stunnel I get the following error message: Clients allowed=500 stunnel 4.56 on x86_64-unknown-linux-gnu platform Compiled/running with OpenSSL 1.0.1 14 Mar 2012 Threading:PTHREAD Sockets:POLL,IPv6 SSL:ENGINE,OCSP,FIPS Reading configuration from file /usr/local/etc/stunnel/stunnel.conf FIPS_mode_set: F06D065: error:0F06D065:common libcrypto routines:FIPS_mode_set:fips mode not supported Line 51: "[pop3s]": Failed to initialize SSL str_stats: 9 block(s), 163 data byte(s), 522 control byte(s) Any assistance would be greatly appreciated. -- Laura J. Fried

1 0

4.53 32-bit on Windows 2k8 R2 64bit
by Michael Curran 01 May '13

01 May '13

We are running stunnel and noticed an issue with what ended up being an issue creating a new thread due to running out of memory at 2gb - error (8) on create_client Are there any known issues with 4.53 around memory usage? We only terminate 2 ports against the installation 443 on 2 different interfaces / IP addresses and we ran into this issue with just under 5000 total connections We are not doing ECDH , but are using a 1024-bit param file

2 3

Problem with roundrobbin failover mode?
by Matt Wise 01 May '13

01 May '13

I've got dozens of clients connecting with Stunnel to a group of 5 servers. Each system has a config that looks like this: > cert = /etc/stunnel/zookeeper.pem > key = /etc/stunnel/zookeeper.key > CAfile = /etc/stunnel/zookeeper_ca.pem > verify = 2 > delay = yes > sslVersion = TLSv1 > client = yes > setuid = stunnel4 > setgid = stunnel4 > pid = /var/lib/stunnel4/zookeeper.stunnel4.pid > socket = l:TCP_NODELAY=1 > socket = r:TCP_NODELAY=1 > TIMEOUTconnect = 2 > session = 86400 > debug = 5 > [zookeeper] > accept = 127.0.0.1:2182 > failover = rr > connect = prod-zookeeper:2182 > connect = prod-zookeeper-1:2182 > connect = prod-zookeeper-2:2182 > connect = prod-zookeeper-3:2182 > connect = prod-zookeeper-4:2182 > connect = prod-zookeeper-5:2182 Essentially the first host is a load balancer, and the next 5 are the actual zookeeper hosts so that we can bypass the ELB if its giving us fits. Now what we're seeing is that almost every connection ends up on prod-zookeeper-5. Over and over and over again, our hosts pick the same system each time. We're running Stunnel 4.52: > Clients allowed=8000 > stunnel 4.52 on i486-pc-linux-gnu platform > Compiled/running with OpenSSL 0.9.8k 25 Mar 2009 > Threading:PTHREAD SSL:ENGINE Auth:LIBWRAP Sockets:POLL,IPv6 Any ideas what might be wrong here? Obviously we want the connections to be *roughly* random across the list of hosts... and if one of the hosts goes down, and the connection fails, we want the stunnel service to try again, and randomly pick a new host. It doesn't really seem to be doing that though. --Matt

3 8

help on Linux stunnel setup
by Valerio.FABRIZIO＠sungard.com 26 Apr '13

26 Apr '13

Hello all! I'm in charge of activating stunnel to connect a service to a remote service. Since I'm totally new on this product, I'd be grateful if someone could help me in configuring. This is where I stand: Stunnel version: stunnel 4.29 on x86_64-unknown-linux-gnu with OpenSSL 1.0.0-fips 29 Mar 2010 OS: Linux 2.6.32-220.23.1.el6.x86_64 #1 SMP Mon Jun 18 18:58:52 BST 2012 x86_64 x86_64 x86_64 GNU/Linux I'd need to have it started by non-root user, and I have loaded under a specific path (owned by the same user): Stunnel.conf: ; Sample stunnel configuration file ;cert = FXMS1.pem client = yes output = /export/home/bg_mtsbv/slev5fix/log pid = /export/home/bg_mtsbv/slev5fix/conf/stunnel.pid [ssl01] accept = 127.0.0.1:18889 connect = 193.203.229.143:443 Stunnel.pid (empty) xxx.pem (certificate has been provided by the owner of the target server) my first two questions: which is the correct command line to be launched? Is it correct to have all the files under the user's directory? Many thanks in advance for your help! Regards, Valerio

1 0

Inconsistent performance across stunnel and/or OpenSSL versions
by PPingPongBaker PPingPongBaker 23 Apr '13

23 Apr '13

Hi All, I am experimenting with stunnel inside a VM on Xenserver 6.02. So this may not be a "common" use case, nonetheless, I would like to point out the issue. It is a basic setup as follows with 3 VMs running "ab" for webclient, stunnel+haproxy combo as the https/http bridge and nginx as the webserver. client VM (ab) <-> stunnel + haproxy VM <-> webserver VM (nginx) Specs on the stunnel VM are 2GB RAM, single-core dedicated 2.5 GHz Xeon E5-2640 vCPU, running Debian Squeeze 2.6.32-5-amd64 (64 bit) kernel. All things unchanged such as stunnel/haproxy/nginx config and taking care of common gotchas such as file descriptor limit, TIMEOUTclose, disabling libwrap, etc. stunnel is built with pthreads. Also stunnel is configured to use a 2K RSA self-signed certificate, and the client is being forced to do TLS1. "ab" is invoked with "-c 4" so as to peg the stunnel VM CPU (any value beyond 4 doesn't seem to matter). nginx serves a tiny 32 byte static html file. With stunnel 4.29 and OpenSSL 0.9.8o, I get 300 requests per second as max throughput. With stunnel 4.56 and OpenSSL 1.0.1e, I get only 40 requests per second as max throughput. tcpdump tells me that the Server Hello sent to the client takes a longer time in the latter case. Tinkering with TCP_NODELAY doesn't change anything. Anyone else seeing this maybe even on physical hardware? Has anything changed in OpenSSL across those versions? Suggestions? Thanks.

4 10

Windows Failover Clustering Support
by Cynthia Haselton 22 Apr '13

22 Apr '13

All, A (hopefully) quick question: Is stunnel supported on Windows Failover Clusters...specifically as a clustered service or to encrypt connections to/from a clustered IP? Thanks in advance, CJH

2 4

Customizing encryption
by John 19 Apr '13

19 Apr '13

HI guys, I need to take off SSL and use another encryption, need some hints since i'm new to stunnel. Thanks in advance,John

1 0

limited number of ports
by Terren Suydam 09 Apr '13

09 Apr '13

Hi, There appears to be a limit to the number of services you can define. Services beyond the 64th service appear to get set up without any log warnings or errors, yet don't pass traffic. The code uses select() & FD_SET to accept() an incoming connection & in Windows (using Windows Server 2008) the default is 64 sockets for that so wondering if I can just recompile, setting FD_SETSIZE to something larger. I'll try it either way, just wanted to put it out there to see if anyone else has ever run into this. Thanks, Terren

4 10

Trying to Upgrade stunnel, but compile isn't working?
by Michael D. Setzer II 03 Apr '13

03 Apr '13

I have been using stunnel for a long time, but was just trying to compile the latest version from source, and it compiles, but doesn't work like the older version, so I must have some option wrong. With the current version on my Fedora 14 machine using the latest version it loads the stunnel ports and works, but the newer version does seem to load or give an error message. I've tested the stunnel from Fedora 16 and Fedora 17, and they work fine with the stunnel.conf to load the settings. Current version info from Fedora 14 system. stunnel 4.34 on x86_64-redhat-linux-gnu with OpenSSL 1.0.0e-fips 6 Sep 2011 Threading:PTHREAD SSL:ENGINE Sockets:POLL,IPv6 Auth:LIBWRAP Global options debug = daemon.notice pid = /var/run/stunnel.pid RNDbytes = 64 RNDfile = /dev/urandom RNDoverwrite = yes Service-level options cert = /etc/stunnel/stunnel.pem ciphers = ALL:!aNULL:!eNULL:!SSLv2 curve = sect163r2 session = 300 seconds stack = 65536 bytes sslVersion = SSLv3 for client, all for server TIMEOUTbusy = 300 seconds TIMEOUTclose = 60 seconds TIMEOUTconnect = 10 seconds TIMEOUTidle = 43200 seconds verify = none The new build does this. stunnel 4.56 on x86_64-unknown-linux-gnu platform Compiled/running with OpenSSL 1.0.0e-fips 6 Sep 2011 Threading:PTHREAD Sockets:POLL,IPv6 SSL:ENGINE,OCSP,FIPS Global options: debug = daemon.notice pid = /usr/local/var/run/stunnel/stunnel.pid RNDbytes = 64 RNDfile = /dev/urandom RNDoverwrite = yes Service-level options: ciphers = FIPS (with "fips = yes") ciphers = ALL:!SSLv2:!aNULL:!EXP:!LOW:-MEDIUM:RC4:+HIGH (with "fips = no") sessionCacheSize = 1000 sessionCacheTimeout = 300 seconds sslVersion = TLSv1 (with "fips = yes") sslVersion = TLSv1 for client, all for server (with "fips = no") stack = 65536 bytes TIMEOUTbusy = 300 seconds TIMEOUTclose = 60 seconds TIMEOUTconnect = 10 seconds TIMEOUTidle = 43200 seconds verify = none Have also tried it with --disable-fips With the new version I have to provide the /etc/stunnel/stunnel.conf, but it doesn't load any of the options. Sure it is just a simple configure setting I am missing. Thanks. +----------------------------------------------------------+ Michael D. Setzer II - Computer Science Instructor Guam Community College Computer Center mailto:[email protected] mailto:[email protected] http://www.guam.net/home/mikes Guam - Where America's Day Begins G4L Disk Imaging Project maintainer http://sourceforge.net/projects/g4l/ +----------------------------------------------------------+ http://setiathome.berkeley.edu (Original) Number of Seti Units Returned: 19,471 Processing time: 32 years, 290 days, 12 hours, 58 minutes (Total Hours: 287,489) BOINC@HOME CREDITS SETI 14305761.074364 | EINSTEIN 10610832.119852 ROSETTA 6726167.419674 | ABC 15903532.519753

2 2

Log Rotation on Windows
by Brian Wilkins 03 Apr '13

03 Apr '13

I know that log rotation on Windows is on the TO-DO list. Is there a way to rotate the log at startup using some other means or during use? I suppose I could start stunnel with a batch file and do the log rotation before starting. Is there any other way? Brian

1 0

32/64 bit interposition on Solaris
by Norm Jacobs 29 Mar '13

29 Mar '13

I was recently working with stunnel on Solaris and ran across the following code in client.c: putenv("LD_PRELOAD=" LIBDIR "/libstunnel.so"); This appears to have been put in place to interpose a stunnel version of getpeername() on the downstream application. This works great when libstunnel.so has the same bittedness as the downstream application, but Solaris allows users to install and run both 32 and 64 bit applications on the same system. If the stunnel exectuable is a 32 bit application and the downstream application is a 64 bit application, the runtime linker falls over because of the mismatch with the interposed library. To avoid this problem, stunnel should use LD_PRELOAD_32 and LD_PRELOAD_64 on Solaris. I have put together a patch to client.c that sets both LD_PRELOAD_* environment variables to something that seems to make sense on Solaris, but have used a fairly hacky way of enabling it when I build. The client.c changes that I put together are: # On Solaris, fix stunnel so that the linker know where both the 32 and 64 bit # interposer libraries are. If you use LD_PRELOAD with the wrong bittedness # of interposer, the runtime linker hits a fatal error in trying to load # mismatched ELF objects. # diff -r -u stunnel-4.55.orig/src/client.c stunnel-4.55/src/client.c --- stunnel-4.55.orig/src/client.c 2013-02-28 00:17:58.000000000 -0800 +++ stunnel-4.55/src/client.c 2013-03-21 22:55:21.098479331 -0700 @@ -1096,9 +1096,14 @@ /* just don't set these variables if getnameinfo() fails */ putenv(str_printf("REMOTE_HOST=%s", host)); if(c->opt->option.transparent_src) { - putenv("LD_PRELOAD=" LIBDIR "/libstunnel.so"); - /* for Tru64 _RLD_LIST is used instead */ +#ifdef MACH64 + putenv("LD_PRELOAD_32=" LIBDIR "/libstunnel.so"); + putenv("LD_PRELOAD_64=" LIBDIR "/" MACH64 "/libstunnel.so"); +#elif __osf /* for Tru64 _RLD_LIST is used instead */ putenv("_RLD_LIST=" LIBDIR "/libstunnel.so:DEFAULT"); +#else + putenv("LD_PRELOAD=" LIBDIR "/libstunnel.so"); +#endif } } This adds more appropriate environment variables into the calling environment on Solaris. It still needs some work to integrate better with the build. Anyway, I thought that I would raise the issue and at least offer a direction to work from. I am happy to work with someone on a better resolution to this. -Norm

1 0