stunnel-users January 2022

5 participants
7 discussions

older browsers, stunnel and privoxy
by kovacs janos 04 Mar '24

04 Mar '24

sorry to bother, im trying to make older browsers be able to display TLS 1.1 and TLS 1.2 sites. i heard stunnel cant be configured to always forward to the current site address dynamically, thats why i would use privoxy. the browser is configured to send to: 127.0.0.1 443 stunnel config has this at the end: [Tunnel_in] client = yes accept = 127.0.0.1:443 connect = 127.0.0.1:8118 verifyChain = yes CAfile = ca-certs.pem checkHost = localhost 127.0.0.1:8118 is the privoxy address. this is what stunnel writes: LOG5[main]: Configuration successful LOG5[0]: Service [Tunnel_in] accepted connection from 127.0.0.1:3261 LOG5[0]: s_connect: connected 127.0.0.1:8118 LOG5[0]: Service [Tunnel_in] connected remote server from 127.0.0.1:3262 and the browser infinitely loads, and never loads anything or leaves the page. if i remove the last 3 lines, its the same just with this line added: LOG4[main]: Service [Tunnel_in] needs authentication to prevent MITM attacks but it doesnt give an error or anything. with a configuration like: [Tunnel_out] client = no accept = 127.0.0.1:443 connect = 127.0.0.1:8118 cert = stunnel.pem this is what it gives: LOG5[3]: Service [Tunnel_out] accepted connection from 127.0.0.1:3294 LOG3[3]: SSL_accept: 1407609B: error:1407609B:SSL routines:SSL23_GET_CLIENT_HELLO:https proxy request LOG5[3]: Connection reset: 0 byte(s) sent to TLS, 0 byte(s) sent to socket and browser gives a server not found error immediately. im not even sure if i should use client or server configuration in a case like this, but none of them works anyway. all i would need is for my browser to get the pages decrypted, or at least in less than TLS1.1. like how on newipnow.com i can access sites with any encryption, since they are sent to the browser without encryption. the browser just gives an "unencrypted tunnel" warning, which is how i found stunnel, and which is exactly what i need, just locally.

8 41

TPM based mutual tls authentication
by Nyiri, Gabor (Nokia - HU/Budapest) 07 Nov '23

07 Nov '23

Hi, Can you help me how to configure stunnel client to use TPM for mutual TLS authentication? I want to connect with mTLS to a remote server then make this connection available for localhost without mTLS. Thanks for your help in advance! Here is my configuration so far without TPM: debug = debug output = /tmp/stunnel.log foreground = yes [mtls_client] client = yes accept = 127.0.0.1:12019 sni = server-with-mtls.example.com checkHost = server-with-mtls.example.com connect = 1.2.3.4:443 verifyChain = yes CApath = /etc/ssl/certs/ cert = client.crt key = client.key Thanks & br, Gábor Nyíri,

2 1

tunnel for IMAP/SMTP
by Caterpillar 12 Feb '22

12 Feb '22

Good day. I need to be able to use Thunderbird to connect to a mail server (IMAP/SMTP) that has an obsolete TLS version (1.1) and I don't want to low the TLS minimum version on my computers. For this need I would like to use stunnel between Thunderbid clients and the mail server. I tried to use tutorial [1] plus "sslVersion = all" option, but I think the guide is quite incomplete. Do you have any other guide/tutoral that is more complete? Thank you [1]: https://petermolnar.com/secure-smtp-and-imap-sessions-with-stunnel/

3 4

New to stunnel! Need help connecting to a REST API
by Tim Townsend 18 Jan '22

18 Jan '22

Hello! I need help! We have an integration from an ERP package to a REST API (Avatax) that will soon be requiring TLS 1.2 connections. Our tech platform does not have built-in support for TLS 1.2, so I'm hoping to be able to use stunnel to make that happen. Where do I start? What would the conf file section look like for this? I don't see this directly discussed in the documentation. Any help appreciated! [cid:[email protected]] Tim Townsend Programmer Earnest & Associates * Profitability Improvement Specialists Voice: 410.766.6076<tel:+14107666076> ext 210 Email: tim.townsend(a)earnestassoc.com<mailto:[email protected]> * Web: earnestassoc.com<http://www.earnestassoc.com/>

1 0

stunnel 5.62 released
by Michał Trojnara 17 Jan '22

17 Jan '22

Dear Users, I have released version 5.62 of stunnel. ### Version 5.62, 2022.01.17, urgency: MEDIUM * New features - Added a bash completion script. * Bugfixes - Fixed a transfer() loop bug. Home page: https://www.stunnel.org/ Download: https://www.stunnel.org/downloads.html SHA-256 hashes: 9cf5bb949022aa66c736c1326554cca27d0641605a6370274edc4951eb5bd339 stunnel-5.62.tar.gz fbfcc5759344bcafff9ff3bc6cf56c7fb75cb1244b76d4934c5d9a3eb7eee32d stunnel-5.62-win64-installer.exe 4b52ed6e4bb8293fdefb10ee8c271400a8c1749254a11b674ff690eae00b3c5e stunnel-5.62-android.zip Best regards, Mike

1 0

Re: stunnel 5.61transfer() loop executes not transferring any data Connection reset: 0 byte(s) sent to TLS, 0 byte(s) sent to socket inetd mode
by Roberto CORRADO 17 Jan '22

17 Jan '22

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi Mike, Good job! Stunnel 5.62 beta 1 work fine! """ 2022.01.16 22:08:47 LOG6[ui]: Initializing inetd mode configuration 2022.01.16 22:08:47 LOG5[ui]: stunnel 5.62 on i586-slackware-linux-gnu platform 2022.01.16 22:08:47 LOG5[ui]: Compiled/running with OpenSSL 1.1.1m 14 Dec 2021 2022.01.16 22:08:47 LOG5[ui]: Threading:PTHREAD Sockets:POLL,IPv6 TLS:ENGINE,OCSP,PSK,SNI Auth:LIBWRAP 2022.01.16 22:08:47 LOG6[ui]: Initializing inetd mode configuration 2022.01.16 22:08:47 LOG5[ui]: Reading configuration from file /etc/stunnel/imaps.conf 2022.01.16 22:08:47 LOG5[ui]: UTF-8 byte order mark not detected 2022.01.16 22:08:47 LOG5[ui]: FIPS mode disabled 2022.01.16 22:08:47 LOG6[ui]: Compression enabled: 0 methods 2022.01.16 22:08:47 LOG6[ui]: stunnel default security level set: 2 2022.01.16 22:08:47 LOG6[ui]: Session resumption enabled 2022.01.16 22:08:47 LOG6[ui]: Loading certificate from file: /etc/stunnel/stunnel.pem 2022.01.16 22:08:47 LOG6[ui]: Certificate loaded from file: /etc/stunnel/stunnel.pem 2022.01.16 22:08:47 LOG6[ui]: Loading private key from file: /etc/stunnel/stunnel.pem 2022.01.16 22:08:47 LOG6[ui]: Private key loaded from file: /etc/stunnel/stunnel.pem 2022.01.16 22:08:47 LOG6[ui]: DH initialization needed for DHE-RSA-AES256-GCM-SHA384 2022.01.16 22:08:47 LOG6[ui]: 4096-bit DH parameters loaded 2022.01.16 22:08:47 LOG5[ui]: Configuration successful 2022.01.16 22:08:47 LOG5[0]: Service [stunnel] accepted connection from 10.19.79.235:41136 2022.01.16 22:08:47 LOG6[0]: Peer certificate not required 2022.01.16 22:08:47 LOG6[0]: No peer certificate received 2022.01.16 22:08:47 LOG6[0]: Session id: 65640462303D0DA1CD16CAB4977F22B04FFB74693150104FC69AB9FBDC48AED9 2022.01.16 22:08:47 LOG6[0]: No peer certificate received 2022.01.16 22:08:47 LOG6[0]: Session id: B9505D917FA6F2E9C8A0EF14D6E4B01C3ED54599271D93E325ED7412CA2AC5F3 2022.01.16 22:08:47 LOG6[0]: TLS accepted: new session negotiated 2022.01.16 22:08:47 LOG6[0]: TLSv1.3 ciphersuite: TLS_AES_256_GCM_SHA384 (256-bit encryption) 2022.01.16 22:08:47 LOG6[0]: Peer temporary key: X25519, 253 bits 2022.01.16 22:08:47 LOG6[0]: Local mode child started (PID=16984) 2022.01.16 22:08:47 LOG6[0]: TLS closed (SSL_read) 2022.01.16 22:08:47 LOG6[0]: Read socket closed (readsocket) 2022.01.16 22:08:47 LOG6[0]: SSL_shutdown successfully sent close_notify alert 2022.01.16 22:08:47 LOG5[0]: Connection closed: 979 byte(s) sent to TLS, 128 byte(s) sent to socket """ Thanks a lot! - -Roberto -----BEGIN PGP SIGNATURE----- iEYEARECAAYFAmHkjDoACgkQWVOoL214ZeGntwCbBtV1G/J2uThR06ftFC+F2XTP KeQAnjnCTOrk26zzcsNsCOQoWg54MWhD =alm2 -----END PGP SIGNATURE----- ----- Original Message ----- Sent: Sunday, January 16, 2022 9:52 PM Michał Trojnara wrote: > Hi Roberto, > > Could you try https://www.stunnel.org/downloads/beta/stunnel-5.62b1.tar.gz ? > > Best regards, > Mike

2 1

I NEED A HELP TO SETUP THE SSL/TLS EMAILS SUPPORT
by Muj 01 Jan '22

01 Jan '22

HI TECHNICAL SUPPORT, FIRSTLY, I AM APOLOGIZING TO YOU FOR WRITING WITH LARGE CAPS ONLY, IT IS BECAUSE RECENTLY I GOT A BRAIN STROKE AND AM NOT RECOVERED YET. AS FOR MY ISSUE, TO UNDERSTAND IT BETTER, THE FOLLOWING IS MY INFO. - I HAVE AN OLD WINDOWS-XP 32BIT OS. - I AM USING TERABYTE 2.99 TO BACKUP AND RESTORE MY OS, BUT LOOSING MANY EMAILS BECAUSE TERABYTE IS NO LONGER SUPPORTING 2.99 VERSION. THEY SUPPORT RESTORING ALL EMAILS BEGINNING FROM 3 VERSION. THEREFORE, THEY HAVE RECOMMENDED ME TO CONTACT YOU DIRECTLY. NOW WHAT I DID SO FAR. - I DOWNLOADED AND INSTALLED YOUR STUNNEL 4.53 - AFTER AUTOMATIC SETTING, EDITING STUNNEL.CONF FILE, MAKING SOME CHANGES IN IT AND SAVING IT, THE SERVER WENT DOWN. ATTACHED PLEASE FIND STUNNEL.CONF TXT FILE. - BECAUSE THE SERVER WENT DOWN, I TRIED TO DOWNLOAD AND INSTALL STUNNEL AGAIN, BUT ALWAYS GOT THE SAME ERROR MESSAGE.PLEASE CAN YOU HELP ME WITH THIS ISSUE? - I HAVE 3 POP3 EMAIL ACCOUNTS AND 1 IMAP. ALL REQUIRE A CONNECTION SECURITY SSL/TLS. *PLEASE, I NEED TO KNOW HOW **TO COMPLETELY REMOVE THE CURRENT STUNNEL PROGRAM AND AFTER THAT, WHAT STUNNEL VERSION I SHOULD **DOWNLOAD AGAIN **TO BE ABLE TO SET IT UP*. AFTER A SUCCESSFUL NEW INSTALLATION I WOULD GIVE YOU MORE NEEDED INFO FOR SETTING UP MY EMAILS. PLEASE LET ME KNOW IN YOUR BEST CONVENIENCE AND HAVE A BEAUTIFUL NEW YEAR 2022. KIND REGARDS, MARTIN

1 0

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

stunnel-users January 2022