stunnel-users

3306 discussions

UTF8 BOM in PSKsecrets file
by Jakob Hirsch 17 May '18

17 May '18

Hi! I just found out (after a while of troubleshooting) that stunnel does not handle UTF-8 BOM in the PSKsecrets file, i.e. the BOM is considered part of the identity (tested with 5.44, 5.45b4 and 5.45b6 on Windows 10 1709). It was a little tricky to figure this out, as the BOM is apparently filtered out in the logs, e.g. the server just says 'No key found for PSK identity "client1"'. Ok, nobody says that this is supported or that you should do it, it just happens automatically when you click "Edit Configuration" in the Windows GUI and click "Save as" (out of convenience, because you will already be in the config directory then), because the sample config has a BOM and Notepad will also insert a BOM in the new file. I don't know how much work it would be to handle the BOM correctly or at least print a warning (didn't look at the code, sorry), a warning in the manual would probably sufficient, as it could be that I'm the first one to stumble over this (at least I didn't find anything about it on the net). Regards (and thanks for this nice piece of software) Jakob

1 0

Windows Server 2012 R2
by Daniel McArdell 17 May '18

17 May '18

Hello, I have joined the mail group in the hope that someone can help with problems I am having running on our Server machine. I downloaded "stunnel-5.45b6-win64-installer" and installed it on our Server. When I run the executable I get: 2018.05.17 12:48:33 LOG5[main]: stunnel 5.45 on x64-pc-msvc-1913 platform 2018.05.17 12:48:33 LOG5[main]: Compiled/running with OpenSSL 1.1.0g 2 Nov 2017 2018.05.17 12:48:33 LOG5[main]: Threading:WIN32 Sockets:SELECT,IPv6 TLS:ENGINE,OCSP,PSK,SNI 2018.05.17 12:48:33 LOG5[main]: Reading configuration from file stunnel.conf 2018.05.17 12:48:33 LOG5[main]: UTF-8 byte order mark detected 2018.05.17 12:48:33 LOG5[main]: Configuration successful The shortcut [cid:[email protected]] I was expecting to get a GUI interface but that does not happen. Can someone tell me what is going wrong. I feel as though I have missed something obvious. Daniel McArdell | Senior Analyst Programmer | Products & Technology | BNZ<http://www.bnz.co.nz/> L6 Custom House, 17 Whitmore St, Wellington 6011 DDI +64 4 4746679 (extn 76679) | F +64 4 4746023 | M +64 29 2220451 | E Daniel_McArdell(a)bnz.co.nz<mailto:[email protected]?Subject=> CAUTION - This message may contain privileged and confidential information intended only for the use of the addressee named above. If you are not the intended recipient of this message you are hereby notified that any use, dissemination, distribution or reproduction of this message is prohibited. This email was sent by the Bank of New Zealand. You can contact us on 0800 ASK BNZ (0800 275 269). Any views expressed in this message are those of the individual sender and may not necessarily reflect the views of Bank of New Zealand.

1 0

stunnel with client-auth via proxy-server
by jack.reacher＠gmx.de 16 May '18

16 May '18

2 1

Stunnel running as service on Windows Server 2008 R2 but Stunnel All Users shortcut on the desktop reports that it server is down?
by Alex Birchall 16 May '18

16 May '18

Hello, I have Stunnel running as a service on a Windows Server 2008 R2. But the shortcut on the desktop "Stunnel All Users", when launched, informs me that the server is down due to an "invalid configuration file". In the config file, if Stunnel is being run as a service, should it be "client = no" or "server = yes"? Many thanks. Best regards, Alex

2 2

SMTP Authentication failed
by Ian Coetzee 15 May '18

15 May '18

Hi List, I have just joined the stunnel community. I am in the process of migrating our mailserver's public facing ports to stunnel for PCI compliance reasons. So far i have managed to get working: - imap (143/tcp) with starttls - imaps (993/tcp) - pop3 (110/tcp) with starttls - pop3s (995/tcp) My trouble is with smtp(25/tcp,587/tcp) with starttls. I have now tried a couple different mail clients and everyone of them tells me that the server does not support the authentication protocols. I have installed stunnel 5.44. Tee relevant parts in my config: [mail2-imap] protocol = imap accept = 143 connect = <mail-fqdn>:143 [mail2-imaps] accept = 993 connect = <mail-fqdn>:143 [mail2-pop3] protocol = pop3 accept = 110 connect = <mail-fqdn>:110 [mail2-pop3s] accept = 995 connect = <mail-fqdn>:110 [mail2-smtp] protocol = smtp accept = 25 connect = <mail-fqdn>:25 [mail2-smtps] accept = 465 connect = <mail-fqdn>:465 [mail2-smtps-submission] debug = 7 protocol = smtp accept = 587 connect = <mail-fqdn>:587 In the logfile I have the following entries upon connecting 2018.04.30 09:20:50 LOG7[5]: Service [mail2-smtps-submission] started 2018.04.30 09:20:50 LOG7[5]: Option TCP_NODELAY set on local socket 2018.04.30 09:20:50 LOG5[5]: Service [mail2-smtps-submission] accepted connection from 41.13.8.49:56890 2018.04.30 09:20:50 LOG6[5]: s_connect: connecting 10.10.11.2:587 2018.04.30 09:20:50 LOG7[5]: s_connect: s_poll_wait 10.10.11.2:587: waiting 10 seconds 2018.04.30 09:20:50 LOG5[5]: s_connect: connected 10.10.11.2:587 2018.04.30 09:20:50 LOG5[5]: Service [mail2-smtps-submission] connected remote server from 10.10.11.11:42466 2018.04.30 09:20:50 LOG7[5]: Option TCP_NODELAY set on remote socket 2018.04.30 09:20:50 LOG7[5]: Remote descriptor (FD=23) initialized 2018.04.30 09:20:50 LOG7[5]: RFC 2487 detected 2018.04.30 09:20:50 LOG7[5]: <- 220 <mail-fqdn> ESMTP Postfix 2018.04.30 09:20:50 LOG7[5]: -> 220 <mail-fqdn> stunnel for ESMTP Postfix 2018.04.30 09:20:51 LOG7[5]: <- EHLO [100.125.153.220] 2018.04.30 09:20:51 LOG7[5]: -> 250-<mail-fqdn> 2018.04.30 09:20:51 LOG7[5]: -> 250 STARTTLS 2018.04.30 09:20:51 LOG7[5]: <- STARTTLS 2018.04.30 09:20:51 LOG7[5]: -> 220 Go ahead 2018.04.30 09:20:51 LOG6[5]: Peer certificate not required 2018.04.30 09:20:51 LOG7[5]: TLS state (accept): before/accept initialization 2018.04.30 09:20:51 LOG7[5]: SNI: no virtual services defined 2018.04.30 09:20:51 LOG7[5]: TLS state (accept): SSLv3 read client hello A 2018.04.30 09:20:51 LOG7[5]: TLS state (accept): SSLv3 write server hello A 2018.04.30 09:20:51 LOG7[5]: TLS state (accept): SSLv3 write certificate A 2018.04.30 09:20:51 LOG7[5]: TLS state (accept): SSLv3 write key exchange A 2018.04.30 09:20:51 LOG7[5]: TLS state (accept): SSLv3 write server done A 2018.04.30 09:20:51 LOG7[5]: TLS state (accept): SSLv3 flush data 2018.04.30 09:20:51 LOG7[5]: TLS state (accept): SSLv3 read client certificate A 2018.04.30 09:20:52 LOG7[5]: TLS state (accept): SSLv3 read client key exchange A 2018.04.30 09:20:52 LOG7[5]: TLS state (accept): SSLv3 read certificate verify A 2018.04.30 09:20:52 LOG7[5]: TLS state (accept): SSLv3 read finished A 2018.04.30 09:20:52 LOG7[5]: TLS state (accept): SSLv3 write change cipher spec A 2018.04.30 09:20:52 LOG7[5]: TLS state (accept): SSLv3 write finished A 2018.04.30 09:20:52 LOG7[5]: TLS state (accept): SSLv3 flush data 2018.04.30 09:20:52 LOG7[5]: New session callback 2018.04.30 09:20:52 LOG7[5]: 2 server accept(s) requested 2018.04.30 09:20:52 LOG7[5]: 2 server accept(s) succeeded 2018.04.30 09:20:52 LOG7[5]: 0 server renegotiation(s) requested 2018.04.30 09:20:52 LOG7[5]: 0 session reuse(s) 2018.04.30 09:20:52 LOG7[5]: 2 internal session cache item(s) 2018.04.30 09:20:52 LOG7[5]: 0 internal session cache fill-up(s) 2018.04.30 09:20:52 LOG7[5]: 0 internal session cache miss(es) 2018.04.30 09:20:52 LOG7[5]: 0 external session cache hit(s) 2018.04.30 09:20:52 LOG7[5]: 0 expired session(s) retrieved 2018.04.30 09:20:52 LOG6[5]: TLS accepted: new session negotiated 2018.04.30 09:20:52 LOG6[5]: No peer certificate received 2018.04.30 09:20:52 LOG6[5]: Negotiated TLSv1.2 ciphersuite ECDHE-RSA-AES128-GCM-SHA256 (128-bit encryption) 2018.04.30 09:20:52 LOG7[5]: Compression: null, expansion: null 2018.04.30 09:20:52 LOG6[5]: Read socket closed (read hangup) 2018.04.30 09:20:52 LOG7[5]: Sending close_notify alert 2018.04.30 09:20:52 LOG7[5]: TLS alert (write): warning: close notify 2018.04.30 09:20:52 LOG6[5]: SSL_shutdown successfully sent close_notify alert 2018.04.30 09:20:52 LOG6[5]: TLS fd: Connection reset by peer (104) 2018.04.30 09:20:52 LOG6[5]: TLS socket closed (SSL_read) 2018.04.30 09:20:52 LOG7[5]: Sent socket write shutdown 2018.04.30 09:20:52 LOG5[5]: Connection closed: 156 byte(s) sent to TLS, 30 byte(s) sent to socket 2018.04.30 09:20:52 LOG7[5]: Remote descriptor (FD=23) closed 2018.04.30 09:20:52 LOG7[5]: Local descriptor (FD=22) closed 2018.04.30 09:20:52 LOG7[5]: Service [mail2-smtps-submission] finished (4 left) This is the error I am getting from K9-Mail The google mail app just tells me: Alpine (linux commandline smtp client) Any advise from the gurus? Kind regards Ian

1 1

Error with negotiation OK
by Alix Janeth Jerez 15 May '18

15 May '18

Hi I am using lastest stunnel version. When i try to send an email, i get: "error permanente de SMTP: 503 Bad sequence of commands". This is the trace generated when I try to send an email. 2018.05.14 12:59:08 LOG5[main]: Reading configuration from file stunnel.conf 2018.05.14 12:59:08 LOG5[main]: UTF-8 byte order mark not detected 2018.05.14 12:59:08 LOG5[main]: FIPS mode disabled 2018.05.14 12:59:08 LOG5[main]: Configuration successful 2018.05.14 12:59:08 LOG7[main]: Binding service [pseudo-ssmtp] 2018.05.14 12:59:08 LOG7[main]: Listening file descriptor created (FD=568) 2018.05.14 12:59:08 LOG7[main]: Option SO_EXCLUSIVEADDRUSE set on accept socket 2018.05.14 12:59:08 LOG7[main]: Service [pseudo-ssmtp] (FD=568) bound to 172.31.41.84:116 2018.05.14 12:59:08 LOG7[main]: Signal pipe is empty 2018.05.14 12:59:22 LOG7[main]: Found 1 ready file descriptor(s) 2018.05.14 12:59:22 LOG7[main]: FD=324 ifds=r-x ofds=r-- 2018.05.14 12:59:22 LOG7[main]: Dispatching signals from the signal pipe 2018.05.14 12:59:22 LOG7[main]: Processing SIGNAL_RELOAD_CONFIG 2018.05.14 12:59:22 LOG7[main]: Running on Windows 6.1 2018.05.14 12:59:22 LOG5[main]: Reading configuration from file stunnel.conf 2018.05.14 12:59:22 LOG5[main]: UTF-8 byte order mark not detected 2018.05.14 12:59:22 LOG5[main]: FIPS mode disabled 2018.05.14 12:59:22 LOG7[main]: Compression disabled 2018.05.14 12:59:22 LOG7[main]: Snagged 64 random bytes from C:/.rnd 2018.05.14 12:59:22 LOG7[main]: Wrote 1024 new random bytes to C:/.rnd 2018.05.14 12:59:22 LOG7[main]: PRNG seeded successfully 2018.05.14 12:59:22 LOG6[main]: Initializing service [pseudo-ssmtp] 2018.05.14 12:59:22 LOG7[main]: Ciphers: HIGH:!DH:!aNULL:!SSLv2 2018.05.14 12:59:22 LOG7[main]: TLS options: 0x03000004 (+0x03000000, 0x00000000) 2018.05.14 12:59:22 LOG6[main]: Loading certificate from file: stunnel.pem 2018.05.14 12:59:22 LOG6[main]: Certificate loaded from file: stunnel.pem 2018.05.14 12:59:22 LOG6[main]: Loading private key from file: stunnel.pem 2018.05.14 12:59:22 LOG6[main]: Private key loaded from file: stunnel.pem 2018.05.14 12:59:22 LOG7[main]: Private key check succeeded 2018.05.14 12:59:22 LOG5[main]: Configuration successful 2018.05.14 12:59:22 LOG7[main]: Unbinding service [pseudo-ssmtp] 2018.05.14 12:59:22 LOG7[main]: Service [pseudo-ssmtp] closed (FD=568) 2018.05.14 12:59:22 LOG7[main]: Service [pseudo-ssmtp] closed 2018.05.14 12:59:22 LOG7[main]: Binding service [pseudo-ssmtp] 2018.05.14 12:59:22 LOG7[main]: Listening file descriptor created (FD=568) 2018.05.14 12:59:22 LOG7[main]: Option SO_EXCLUSIVEADDRUSE set on accept socket 2018.05.14 12:59:22 LOG7[main]: Service [pseudo-ssmtp] (FD=568) bound to 172.31.41.84:116 2018.05.14 12:59:22 LOG7[main]: Signal pipe is empty 2018.05.14 12:59:34 LOG7[main]: Found 1 ready file descriptor(s) 2018.05.14 12:59:34 LOG7[main]: FD=324 ifds=r-x ofds=--- 2018.05.14 12:59:34 LOG7[main]: Service [pseudo-ssmtp] accepted (FD=584) from 172.31.41.84:53557 2018.05.14 12:59:34 LOG7[main]: Creating a new thread 2018.05.14 12:59:34 LOG7[main]: New thread created 2018.05.14 12:59:34 LOG7[37]: Service [pseudo-ssmtp] started 2018.05.14 12:59:34 LOG7[37]: Option TCP_NODELAY set on local socket 2018.05.14 12:59:34 LOG5[37]: Service [pseudo-ssmtp] accepted connection from 172.31.41.84:53557 2018.05.14 12:59:34 LOG6[37]: failover: round-robin, starting at entry #1 2018.05.14 12:59:34 LOG6[37]: s_connect: connecting 212.227.15.158:465 2018.05.14 12:59:34 LOG7[37]: s_connect: s_poll_wait 212.227.15.158:465: waiting 10 seconds 2018.05.14 12:59:34 LOG5[37]: s_connect: connected 212.227.15.158:465 2018.05.14 12:59:34 LOG5[37]: Service [pseudo-ssmtp] connected remote server from 172.31.41.84:53558 2018.05.14 12:59:34 LOG7[37]: Option TCP_NODELAY set on remote socket 2018.05.14 12:59:34 LOG7[37]: Remote descriptor (FD=552) initialized 2018.05.14 12:59:34 LOG6[37]: SNI: sending servername: smtp.1and1.es 2018.05.14 12:59:34 LOG6[37]: Peer certificate required 2018.05.14 12:59:34 LOG7[37]: TLS state (connect): before/connect initialization 2018.05.14 12:59:34 LOG7[37]: TLS state (connect): SSLv2/v3 write client hello A 2018.05.14 12:59:34 LOG7[37]: TLS state (connect): SSLv3 read server hello A 2018.05.14 12:59:34 LOG7[37]: Verification started at depth=2: C=US, O="thawte, Inc.", OU=Certification Services Division, OU="(c) 2006 thawte, Inc. - For authorized use only", CN=thawte Primary Root CA 2018.05.14 12:59:34 LOG7[37]: CERT: Pre-verification succeeded 2018.05.14 12:59:34 LOG7[37]: OCSP: Ignoring root certificate 2018.05.14 12:59:34 LOG6[37]: Certificate accepted at depth=2: C=US, O="thawte, Inc.", OU=Certification Services Division, OU="(c) 2006 thawte, Inc. - For authorized use only", CN=thawte Primary Root CA 2018.05.14 12:59:34 LOG7[37]: Verification started at depth=1: C=US, O="thawte, Inc.", CN=thawte SSL CA - G2 2018.05.14 12:59:34 LOG7[37]: CERT: Pre-verification succeeded 2018.05.14 12:59:34 LOG5[37]: OCSP: Connecting the AIA responder "http://t2.symcb.com" 2018.05.14 12:59:34 LOG6[37]: s_connect: connecting 23.5.251.27:80 2018.05.14 12:59:34 LOG7[37]: s_connect: s_poll_wait 23.5.251.27:80: waiting 10 seconds 2018.05.14 12:59:34 LOG5[37]: s_connect: connected 23.5.251.27:80 2018.05.14 12:59:34 LOG7[37]: OCSP: Connected t2.symcb.com:80 2018.05.14 12:59:34 LOG7[37]: OCSP: Response received 2018.05.14 12:59:34 LOG6[37]: OCSP: Status: good 2018.05.14 12:59:34 LOG6[37]: OCSP: This update: May 13 18:15:02 2018 GMT 2018.05.14 12:59:34 LOG6[37]: OCSP: Next update: May 20 18:15:02 2018 GMT 2018.05.14 12:59:34 LOG5[37]: OCSP: Certificate accepted 2018.05.14 12:59:34 LOG6[37]: Certificate accepted at depth=1: C=US, O="thawte, Inc.", CN=thawte SSL CA - G2 2018.05.14 12:59:34 LOG7[37]: Verification started at depth=0: C=DE, ST=Rheinland-Pfalz, L=Montabaur, O=1&1 Internet SE, CN=smtp.1and1.es 2018.05.14 12:59:34 LOG7[37]: CERT: Pre-verification succeeded 2018.05.14 12:59:34 LOG6[37]: CERT: Host name "smtp.1and1.es" matched with "smtp.1and1.es" 2018.05.14 12:59:34 LOG5[37]: OCSP: Connecting the AIA responder "http://tj.symcd.com" 2018.05.14 12:59:34 LOG6[37]: s_connect: connecting 23.5.251.27:80 2018.05.14 12:59:34 LOG7[37]: s_connect: s_poll_wait 23.5.251.27:80: waiting 10 seconds 2018.05.14 12:59:35 LOG5[37]: s_connect: connected 23.5.251.27:80 2018.05.14 12:59:35 LOG7[37]: OCSP: Connected tj.symcd.com:80 2018.05.14 12:59:35 LOG7[37]: OCSP: Response received 2018.05.14 12:59:35 LOG6[37]: OCSP: Status: good 2018.05.14 12:59:35 LOG6[37]: OCSP: This update: May 14 01:38:59 2018 GMT 2018.05.14 12:59:35 LOG6[37]: OCSP: Next update: May 21 01:38:59 2018 GMT 2018.05.14 12:59:35 LOG5[37]: OCSP: Certificate accepted 2018.05.14 12:59:35 LOG5[37]: Certificate accepted at depth=0: C=DE, ST=Rheinland-Pfalz, L=Montabaur, O=1&1 Internet SE, CN=smtp.1and1.es 2018.05.14 12:59:35 LOG7[37]: TLS state (connect): SSLv3 read server certificate A 2018.05.14 12:59:35 LOG7[37]: TLS state (connect): SSLv3 read server key exchange A 2018.05.14 12:59:35 LOG6[37]: Client certificate not requested 2018.05.14 12:59:35 LOG7[37]: TLS state (connect): SSLv3 read server done A 2018.05.14 12:59:35 LOG7[37]: TLS state (connect): SSLv3 write client key exchange A 2018.05.14 12:59:35 LOG7[37]: TLS state (connect): SSLv3 write change cipher spec A 2018.05.14 12:59:35 LOG7[37]: TLS state (connect): SSLv3 write finished A 2018.05.14 12:59:35 LOG7[37]: TLS state (connect): SSLv3 flush data 2018.05.14 12:59:35 LOG7[37]: TLS state (connect): SSLv3 read finished A 2018.05.14 12:59:35 LOG7[37]: 1 client connect(s) requested 2018.05.14 12:59:35 LOG7[37]: 1 client connect(s) succeeded 2018.05.14 12:59:35 LOG7[37]: 0 client renegotiation(s) requested 2018.05.14 12:59:35 LOG7[37]: 0 session reuse(s) 2018.05.14 12:59:35 LOG6[37]: TLS connected: new session negotiated 2018.05.14 12:59:35 LOG7[37]: Peer certificate was cached (5543 bytes) 2018.05.14 12:59:35 LOG6[37]: Negotiated TLSv1.2 ciphersuite ECDHE-RSA-AES256-GCM-SHA384 (256-bit encryption) 2018.05.14 12:59:35 LOG7[37]: Compression: null, expansion: null 2018.05.14 12:59:53 LOG3[36]: transfer: s_poll_wait: TIMEOUTclose exceeded: closing 2018.05.14 12:59:53 LOG5[36]: Connection closed: 15 byte(s) sent to TLS, 166 byte(s) sent to socket I can't find the error. Thanks in advance for your help. Best regards, Alix

2 5

stunnel-5.44 fails cross compile due to wrong include path in Gentoo....fix available
by Joe Harvell 14 May '18

14 May '18

The src/Makefile.am hardcodes -I/usr/kerberos/include. When cross compiling it should be including -I$(SYSROOT)//usr/kerberos/include. I patched configure.ac and Makefile.am, taking advantage of the existing --with-sysroot configure option. The Gentoo bug report: https://bugs.gentoo.org/654374 The patch to configure.ac and Makefile.am: https://654374.bugs.gentoo.org/attachment.cgi?id=528968 I was unable to find a bug reporting system for stunnel. So I guess this is it. Please source this fix. --- Joe Harvell

1 1

help with tls config in stunnel
by Daniel Trickett 10 May '18

10 May '18

Hi, We are running stunnel 5.44 on Solaris. Our b2b legacy system is using TLS 1.0. We have a supplier who recently switched to TLS 1.2 and we can no longer connect to the site from our b2b. How can I configure stunnel to connect to the supplier site using TLS 1.2? TIA. Dan T This message and any attachment are confidential and may be privileged or otherwise protected from disclosure. If you are not the intended recipient, you must not copy this message or attachment or disclose the contents to any other person. If you have received this transmission in error, please notify the sender immediately and delete the message and any attachment from your system. Merck KGaA, Darmstadt, Germany and any of its subsidiaries do not accept liability for any omissions or errors in this message which may arise as a result of E-Mail-transmission or for damages resulting from any unauthorized changes of the content of this message and any attachment thereto. Merck KGaA, Darmstadt, Germany and any of its subsidiaries do not guarantee that this message is free of viruses and does not accept liability for any damages caused by any virus transmitted therewith. Click http://www.emdgroup.com/emd/imprint/mail_disclaimer.html to access the German, French, Spanish and Portuguese versions of this disclaimer.

1 0

How to tell if commuications are encrypted?
by Alex Birchall 10 May '18

10 May '18

Hello, I have Stunnel installed on Windows Server 2008 R2, running as a service. I have it installed as a client on a Windows POS 2009 device. This setup is working, in that the client is operating correctly and using Stunnel. But how can I tell if communications between the Stunnel client and the Stunnel server are being encrypted, rather than Stunnel just doing port forwarding? I did read the client needs to have access to the server's certificate, but at the moment it does not. Alex

2 1

Stunnel to Outlook
by DPS Support 09 May '18

09 May '18

I am trying to get a device on my network to send pop email notifications to my outlook account but can't seem to get it to work. I have enabled the outlook account to accept pop and enabled the client to send them. I'm not sure if I'm missing something or what, any help would be greatly appreciated. Here is my config: debug = info output = stunnel.log [outlook-pop3] client = yes accept = 110 connect = pop-mail.outlook.com:995 [outlook-imap] client = yes accept = 143 connect = imap-mail.outlook.com:993 [outlook-smtp] protocol = smtp client = yes accept = 25 connect = smtp-mail.outlook.com:587 Here is the log as well: 2018.05.08 15:15:03 LOG5[main]: stunnel 5.44 on x86-pc-msvc-1500 platform 2018.05.08 15:15:03 LOG5[main]: Compiled/running with OpenSSL 1.0.2m-fips 2 Nov 2017 2018.05.08 15:15:03 LOG5[main]: Threading:WIN32 Sockets:SELECT,IPv6 TLS:ENGINE,FIPS,OCSP,PSK,SNI 2018.05.08 15:15:03 LOG5[main]: Reading configuration from file stunnel.conf 2018.05.08 15:15:03 LOG5[main]: UTF-8 byte order mark detected 2018.05.08 15:15:03 LOG5[main]: FIPS mode disabled 2018.05.08 15:15:03 LOG6[main]: Initializing service [outlook-pop3] 2018.05.08 15:15:03 LOG4[main]: Service [outlook-pop3] needs authentication to prevent MITM attacks 2018.05.08 15:15:03 LOG6[main]: Initializing service [outlook-imap] 2018.05.08 15:15:03 LOG4[main]: Service [outlook-imap] needs authentication to prevent MITM attacks 2018.05.08 15:15:03 LOG6[main]: Initializing service [outlook-smtp] 2018.05.08 15:15:03 LOG4[main]: Service [outlook-smtp] needs authentication to prevent MITM attacks 2018.05.08 15:15:03 LOG5[main]: Configuration successful 2018.05.08 15:15:03 LOG5[main]: Logging to C:\Users\dps_engineer\AppData\Local\stunnel.log 2018.05.08 15:15:53 LOG5[0]: Service [outlook-pop3] accepted connection from 126.10.230.254:52629 2018.05.08 15:15:53 LOG6[0]: failover: round-robin, starting at entry #1 2018.05.08 15:15:53 LOG6[0]: s_connect: connecting 40.97.135.130:995 2018.05.08 15:15:53 LOG5[0]: s_connect: connected 40.97.135.130:995 2018.05.08 15:15:53 LOG5[0]: Service [outlook-pop3] connected remote server from 126.10.218.222:60145 2018.05.08 15:15:53 LOG6[0]: SNI: sending servername: pop-mail.outlook.com 2018.05.08 15:15:53 LOG6[0]: Peer certificate not required 2018.05.08 15:15:54 LOG6[0]: Certificate verification disabled 2018.05.08 15:15:54 LOG6[0]: Certificate verification disabled 2018.05.08 15:15:54 LOG6[0]: Client certificate not requested 2018.05.08 15:15:54 LOG6[0]: TLS connected: new session negotiated 2018.05.08 15:15:54 LOG6[0]: Negotiated TLSv1.2 ciphersuite ECDHE-RSA-AES256-GCM-SHA384 (256-bit encryption) 2018.05.08 15:15:55 LOG6[0]: Read socket closed (readsocket) 2018.05.08 15:15:55 LOG6[0]: SSL_shutdown successfully sent close_notify alert 2018.05.08 15:15:55 LOG6[0]: TLS socket closed (SSL_read) 2018.05.08 15:15:55 LOG5[0]: Connection closed: 58 byte(s) sent to TLS, 253 byte(s) sent to socket 2018.05.08 15:15:55 LOG5[1]: Service [outlook-smtp] accepted connection from 126.10.230.254:52639 2018.05.08 15:15:55 LOG6[1]: failover: round-robin, starting at entry #2 2018.05.08 15:15:55 LOG6[1]: s_connect: connecting 40.97.162.162:587 2018.05.08 15:15:55 LOG5[1]: s_connect: connected 40.97.162.162:587 2018.05.08 15:15:55 LOG5[1]: Service [outlook-smtp] connected remote server from 126.10.218.222:60147 2018.05.08 15:15:55 LOG6[1]: SNI: sending servername: smtp-mail.outlook.com 2018.05.08 15:15:55 LOG6[1]: Peer certificate not required 2018.05.08 15:15:55 LOG6[1]: Certificate verification disabled 2018.05.08 15:15:55 LOG6[1]: Certificate verification disabled 2018.05.08 15:15:55 LOG6[1]: Empty client CA list 2018.05.08 15:15:55 LOG6[1]: TLS connected: new session negotiated 2018.05.08 15:15:55 LOG6[1]: Negotiated TLSv1.2 ciphersuite ECDHE-RSA-AES256-GCM-SHA384 (256-bit encryption) 2018.05.08 15:16:00 LOG6[1]: TLS socket closed (SSL_read) 2018.05.08 15:16:00 LOG5[1]: Connection closed: 50 byte(s) sent to TLS, 194 byte(s) sent to socket 2018.05.08 15:16:00 LOG5[2]: Service [outlook-pop3] accepted connection from 126.10.230.254:52644 2018.05.08 15:16:00 LOG6[2]: failover: round-robin, starting at entry #2 2018.05.08 15:16:00 LOG6[2]: s_connect: connecting 40.97.161.50:995 2018.05.08 15:16:00 LOG5[2]: s_connect: connected 40.97.161.50:995 2018.05.08 15:16:00 LOG5[2]: Service [outlook-pop3] connected remote server from 126.10.218.222:60149 2018.05.08 15:16:00 LOG6[2]: SNI: sending servername: pop-mail.outlook.com 2018.05.08 15:16:00 LOG6[2]: Peer certificate not required 2018.05.08 15:16:00 LOG6[2]: Certificate verification disabled 2018.05.08 15:16:00 LOG6[2]: Certificate verification disabled 2018.05.08 15:16:00 LOG6[2]: Client certificate not requested 2018.05.08 15:16:00 LOG6[2]: TLS connected: new session negotiated 2018.05.08 15:16:00 LOG6[2]: Negotiated TLSv1.2 ciphersuite ECDHE-RSA-AES256-GCM-SHA384 (256-bit encryption) 2018.05.08 15:16:01 LOG6[2]: TLS socket closed (SSL_read) 2018.05.08 15:16:01 LOG5[2]: Connection closed: 58 byte(s) sent to TLS, 253 byte(s) sent to socket 2018.05.08 15:16:01 LOG5[3]: Service [outlook-smtp] accepted connection from 126.10.230.254:52647 2018.05.08 15:16:01 LOG6[3]: failover: round-robin, starting at entry #3 2018.05.08 15:16:01 LOG6[3]: s_connect: connecting 40.97.162.146:587 2018.05.08 15:16:01 LOG5[3]: s_connect: connected 40.97.162.146:587 2018.05.08 15:16:01 LOG5[3]: Service [outlook-smtp] connected remote server from 126.10.218.222:60150 2018.05.08 15:16:01 LOG6[3]: SNI: sending servername: smtp-mail.outlook.com 2018.05.08 15:16:01 LOG6[3]: Peer certificate not required 2018.05.08 15:16:01 LOG6[3]: Certificate verification disabled 2018.05.08 15:16:01 LOG6[3]: Certificate verification disabled 2018.05.08 15:16:01 LOG6[3]: Empty client CA list 2018.05.08 15:16:01 LOG6[3]: TLS connected: new session negotiated 2018.05.08 15:16:01 LOG6[3]: Negotiated TLSv1.2 ciphersuite ECDHE-RSA-AES256-GCM-SHA384 (256-bit encryption) 2018.05.08 15:16:03 LOG6[cron]: Executing cron jobs 2018.05.08 15:16:03 LOG6[cron]: Cron jobs completed in 0 seconds 2018.05.08 15:16:06 LOG6[3]: TLS socket closed (SSL_read) 2018.05.08 15:16:06 LOG5[3]: Connection closed: 50 byte(s) sent to TLS, 194 byte(s) sent to socket 2018.05.08 15:16:06 LOG5[4]: Service [outlook-pop3] accepted connection from 126.10.230.254:52653 2018.05.08 15:16:06 LOG6[4]: failover: round-robin, starting at entry #3 2018.05.08 15:16:06 LOG6[4]: s_connect: connecting 40.97.134.18:995 2018.05.08 15:16:06 LOG5[4]: s_connect: connected 40.97.134.18:995 2018.05.08 15:16:06 LOG5[4]: Service [outlook-pop3] connected remote server from 126.10.218.222:60153 2018.05.08 15:16:06 LOG6[4]: SNI: sending servername: pop-mail.outlook.com 2018.05.08 15:16:06 LOG6[4]: Peer certificate not required 2018.05.08 15:16:06 LOG6[4]: Certificate verification disabled 2018.05.08 15:16:06 LOG6[4]: Certificate verification disabled 2018.05.08 15:16:06 LOG6[4]: Client certificate not requested 2018.05.08 15:16:06 LOG6[4]: TLS connected: new session negotiated 2018.05.08 15:16:06 LOG6[4]: Negotiated TLSv1.2 ciphersuite ECDHE-RSA-AES256-GCM-SHA384 (256-bit encryption) 2018.05.08 15:16:07 LOG6[4]: Read socket closed (readsocket) 2018.05.08 15:16:07 LOG6[4]: SSL_shutdown successfully sent close_notify alert 2018.05.08 15:16:07 LOG6[4]: TLS socket closed (SSL_read) 2018.05.08 15:16:07 LOG5[4]: Connection closed: 58 byte(s) sent to TLS, 253 byte(s) sent to socket 2018.05.08 15:16:07 LOG5[5]: Service [outlook-smtp] accepted connection from 126.10.230.254:52656 2018.05.08 15:16:07 LOG6[5]: failover: round-robin, starting at entry #4 2018.05.08 15:16:07 LOG6[5]: s_connect: connecting 2603:1036:101::2:587 2018.05.08 15:16:07 LOG3[5]: s_connect: connect 2603:1036:101::2:587: Network is unreachable (WSAENETUNREACH) (10051) 2018.05.08 15:16:07 LOG6[5]: s_connect: connecting 2603:1036:102:108::2:587 2018.05.08 15:16:07 LOG3[5]: s_connect: connect 2603:1036:102:108::2:587: Network is unreachable (WSAENETUNREACH) (10051) 2018.05.08 15:16:07 LOG6[5]: s_connect: connecting 2603:1036:102:cc::2:587 2018.05.08 15:16:07 LOG3[5]: s_connect: connect 2603:1036:102:cc::2:587: Network is unreachable (WSAENETUNREACH) (10051) 2018.05.08 15:16:07 LOG6[5]: s_connect: connecting 2603:1036:102:8f::2:587 2018.05.08 15:16:07 LOG3[5]: s_connect: connect 2603:1036:102:8f::2:587: Network is unreachable (WSAENETUNREACH) (10051) 2018.05.08 15:16:07 LOG6[5]: s_connect: connecting 40.97.161.50:587 2018.05.08 15:16:08 LOG5[5]: s_connect: connected 40.97.161.50:587 2018.05.08 15:16:08 LOG5[5]: Service [outlook-smtp] connected remote server from 126.10.218.222:60158 2018.05.08 15:16:08 LOG6[5]: SNI: sending servername: smtp-mail.outlook.com 2018.05.08 15:16:08 LOG6[5]: Peer certificate not required 2018.05.08 15:16:08 LOG6[5]: Certificate verification disabled 2018.05.08 15:16:08 LOG6[5]: Certificate verification disabled 2018.05.08 15:16:08 LOG6[5]: Empty client CA list 2018.05.08 15:16:08 LOG6[5]: TLS connected: new session negotiated 2018.05.08 15:16:08 LOG6[5]: Negotiated TLSv1.2 ciphersuite ECDHE-RSA-AES256-GCM-SHA384 (256-bit encryption) 2018.05.08 15:16:13 LOG6[5]: TLS socket closed (SSL_read) 2018.05.08 15:16:13 LOG5[5]: Connection closed: 50 byte(s) sent to TLS, 194 byte(s) sent to socket Sent from Outlook<http://aka.ms/weboutlook>

2 1

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

stunnel-users