[stunnel-users] Session is active but I cannot connect

Thu Apr 9 17:49:25 CEST 2015

The key error message is
bind: Address already in use (98)
You can' set both accept and connect to the same port.

See if you can configure your jdbc app on the server to listen on loopback interfase, line 127.0.0.1:2404, then set accept=yourserveraddress:2406 and connect=127.0.0.1:2404

-----Original Message-----
From: daninho dj <daninho.dj at gmail.com>
Date: Thu, 9 Apr 2015 17:30:55 
To: <cbrowne at cbcs-usa.com>
Cc: <josealf at rocketmail.com>; <stunnel-users at stunnel.org>
Subject: Re: [stunnel-users] Session is active but I cannot connect

It was typo sorry. The settings on the server are:

[test]
accept = 2406
connect = 2404

and on the client:

[jdbc]
client = yes
accept = 127.0.0.1:2404
connect = my_server_name:2406

I'm trying to start the service on the server and it's not working:

/etc/init.d/stunnel start
Starting stunnel (SSL tunnel) startproc:  exit status of parent of
/usr/sbin/stunnel: 1
  please see /var/log/rc.stunnel.log for details

      failed

Regards,

On Thu, Apr 9, 2015 at 5:04 PM, Carter Browne <cbcs at comcast.net> wrote:

>  In your before setting, your client should have  been to connect to your
> test server:
>
> [jdbc]
> client = yes
> accept = 127.0.0.1:2404
> connect=my_server_name:2404
>
> In your after setting, the accept and connect ports cannot be the same
> port.
>
>
>
>
> On 4/9/2015 10:51 AM, daninho dj wrote:
>
> Hi Jose,
>
>  Thanks for mail. The problem is that when I change the accept port on
> the server, stunnel doesn't start:
>
>  *Before:*
>
>  *Server:*
>
>  [test]
> accept = 2404
> connect = 2406
>
>  *Client:*
>
>  [jdbc]
> client = yes
> accept = 127.0.0.1:2404
> connect = *my_server_name*:2406
>
>  *After:*
>
>  I edited the stunnel.conf on the server:
>
>  [test]
> accept = 2406
> connect = 2406
>
>  Then trying to start the service:
>
>  */etc/init.d/stunnel start*
> *Starting stunnel (SSL tunnel) startproc:  exit status of parent of
> /usr/sbin/stunnel: 1*
> *  please see /var/log/rc.stunnel.log for details
>
>         failed*
>
>  /var/log/rc.stunnel.log is empty but in the log specified in the
> stunnel.conf I have the following:
>
>  tail -10 /var/log/stunnel/stunnel.log
> 2015.04.09 16:42:36 LOG5[22524:139805264570112]: Threading:PTHREAD
> SSL:ENGINE Sockets:POLL,IPv6 Auth:LIBWRAP
> 2015.04.09 16:42:36 LOG6[22524:139805264570112]: file ulimit = 262144 (can
> be changed with 'ulimit -n')
> 2015.04.09 16:42:36 LOG6[22524:139805264570112]: poll() used - no
> FD_SETSIZE limit for file descriptors
> 2015.04.09 16:42:36 LOG5[22524:139805264570112]: 128000 clients allowed
> 2015.04.09 16:42:36 LOG7[22524:139805264570112]: FD 10 in non-blocking mode
> 2015.04.09 16:42:36 LOG7[22524:139805264570112]: FD 11 in non-blocking mode
> 2015.04.09 16:42:36 LOG7[22524:139805264570112]: FD 12 in non-blocking mode
> 2015.04.09 16:42:36 LOG7[22524:139805264570112]: SO_REUSEADDR option set
> on accept socket
> 2015.04.09 16:42:36 LOG3[22524:139805264570112]: Error binding test to
> 0.0.0.0:2406
> 2015.04.09 16:42:36 LOG3[22524:139805264570112]: bind: Address already in
> use (98)
>
>
>  Same thing happens when I try to change the ports on the client. Any
> idea how this problem can be solved?
>
>  Thanks and regards,
> Daninho
>
>
>
>
>
> On Thu, Apr 9, 2015 at 4:12 PM, <josealf at rocketmail.com> wrote:
>
>>
>> The accept port on the server Config must be the same as the connect port
>> on the client config.
>> The connect port on the server must be the port used by the
>> application/service you try to secure, usually bound to the loopback
>> interfase, as you probably don't want to allow unsecure connections.
>> On the client the accept port is the port your client application will
>> connect to.
>>
>> Hope this helps to clarify a bit.
>>
>> Regards
>>
>> -----Original Message-----
>> From: daninho dj <daninho.dj at gmail.com>
>> Sender: "stunnel-users" <stunnel-users-bounces at stunnel.org>
>> Date: Thu, 9 Apr 2015 14:28:25
>> To: <stunnel-users at stunnel.org>
>> Subject: [stunnel-users] Session is active but I cannot connect
>>
>> _______________________________________________
>> stunnel-users mailing list
>> stunnel-users at stunnel.org
>> https://www.stunnel.org/cgi-bin/mailman/listinfo/stunnel-users
>>
>
>
>
>  --
> daninho <http://daninhodj.com>
>
>
> _______________________________________________
> stunnel-users mailing liststunnel-users at stunnel.orghttps://www.stunnel.org/cgi-bin/mailman/listinfo/stunnel-users
>
>
> --
> Carter Brownecbrowne at cbcs-usa.com
>
>

-- 
daninho <http://daninhodj.com>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.stunnel.org/pipermail/stunnel-users/attachments/20150409/f87c04ae/attachment.html>